본문으로 건너뛰기
공식 EU 표시명용어집 항목 15877

MALEIC ANHYDRIDE

이 기록은 EU 화장품 표시에 사용하는 공식 일반 원료 명칭을 확인해 줍니다. 그것만으로는 해당 물질이 허용되거나 제한이 없거나 안전하다는 것이 확인되지 않습니다.

글로벌 근거 요약

확인된 정체는 색인된 시장 데이터세트 13개 중 0개에서 일치하는 규제 근거가 있습니다: 국가 기록 0건과 EU 부속서 기록 0건. 모든 결과와 근거 부족 사항은 아래에 나열되어 있습니다.

근거가 있는 시장 0곳
확인한 시장
13
근거가 있는 시장
0
근거 부족
13
확인된 식별자
2

확인된 물질 정체

CAS:108-31-6
EC:203-571-6
원료 색인 기록:
MALEIC ANHYDRIDE
화장품 기능: FILM FORMING

2,5 Furandione

일치 또는 보고된 명칭 1개
MALEIC ANHYDRIDE

시장별 규제 근거

여기에서 추적하는 시장 13곳 중 어느 곳에도 MALEIC ANHYDRIDE이라는 명칭으로 가져온 규칙이 없습니다.

이는 이 목록에 관한 설명이지 법에 관한 설명이 아닙니다. 가져온 규칙이 없다는 것이 해당 물질이 허용된다는 근거는 아닙니다. 규칙은 다른 명칭으로, 이 용어집 항목에 없는 CAS 또는 EC 번호로, 또는 아직 가져오지 않은 데이터세트에 존재할 수 있습니다.

화학적 정체 및 특성

CAS 108-31-6의 PubChem 2D 화학 구조
CAS 108-31-6PubChem CID 7923

Maleic Anhydride

Maleic anhydride appears as colorless crystalline needles, flakes, pellets, rods, briquettes, lumps or a fused mass. Melts at 113 °F. Shipped both as a solid and in the molten state. Vapors, fumes and dusts strong irritate the eyes, skin and mucous membranes. Flash point 218 °F. Autoignition temperature 890 °F. Used to make paints and plastics and other chemicals. — CAMEO Chemicals

IUPAC 명칭
furan-2,5-dione
분자식
C4H2O3
분자량
98.06 g/mol
정확한 질량
98.000393922 Da
XLogP3
-0.1
위상 극성 표면적
43.4 Ų
수소 결합 공여체
0
수소 결합 수용체
3
공유결합 단위
1
정의된 입체중심
0

다른 이름

2,5-FurandioneToxilic anhydrideMaleic acid anhydridecis-Butenedioic anhydrideDihydro-2,5-dioxofuranMaleinanhydridRCRA waste number U1472,5-Furanedione
보고된 명칭 16개 더 보기
Anhydrid kyseliny maleinoveCHEBI:474859V5877ZJZ25NSC-137651Anhydride, MaleicRefChem:5978203-571-6606-024-32,5-dihydrofuran-2,5-dioneNSC 137651C4H2O3Trelagliptin Impurity 58Maleic AnhydridesMaleic anhydride-13C4Maleinanhydrid [Czech]MALEICANHYDRIDE
외부 데이터베이스 식별자

추가 과학 데이터베이스의 근거

NIH PubChem PUG-View
식별자 정확히 일치7923

Attributed physical-property, hazard, environmental and use annotations.

  • First Aid: EYES: First check the victim for contact lenses and remove if present. Flush victim's eyes with water or normal saline solution for 20 to 30 minutes while simultaneously calling a hospital or poison control center. Do not put any ointments, oils, or medication in the victim's eyes without specific instructions from a physician. IMMEDIATELY transport the victim after flushing eyes to a hospital even if no symptoms (such as redness or irritation) develop.; SKIN: IMMEDIATELY flood affected skin with water while removing and isolating all contaminated clothing. Gently wash all affected skin areas thoroughly with soap and water. IMMEDIATELY call a hospital or poison control center even if no symptoms (such as redness or irritation) develop. IMMEDIATELY transport the victim to a hospital for treatment after washing the affected areas.; INHALATION: IMMEDIATELY leave the contaminated area; take deep breaths of fresh air. If symptoms (such as wheezing, coughing, shortness of breath, or burning in the mouth, throat, or chest) develop, call a physician and be prepared to transport the victim to a hospital. Provide proper respiratory protection to rescuers entering an unknown atmosphere. Whene 출처: CAMEO Chemicals
  • ERG2024, Guide 156 (Maleic anhydride): General First Aid:; · Call 911 or emergency medical service.; · Ensure that medical personnel are aware of the material(s) involved, take precautions to protect themselves and avoid contamination.; · Move victim to fresh air if it can be done safely.; · Administer oxygen if breathing is difficult.; · If victim is not breathing:; -- DO NOT perform mouth-to-mouth resuscitation; the victim may have ingested or inhaled the substance.; -- If equipped and pulse detected, wash face and mouth, then give artificial respiration using a proper respiratory medical device (bag-valve mask, pocket mask equipped with a one-way valve or other device).; -- If no pulse detected or no respiratory medical device available, provide continuous compressions. Conduct a pulse check every two minutes or monitor for any signs of spontaneous respirations.; · Remove and isolate contaminated clothing and shoes.; · For minor skin contact, avoid spreading material on unaffected skin.; · In case of contact with substance, remove immediately by flushing skin or eyes with running water for at least 20 minutes.; · For severe burns, immediate medical attention is required.; · Effects of exposure (inhalation, ingestion, 출처: Emergency Response Guidebook (ERG)
  • First Aid: (General first aid procedures); Eye: Irrigate immediately - If this chemical contacts the eyes, immediately wash (irrigate) the eyes with large amounts of water, occasionally lifting the lower and upper lids. Get medical attention immediately.; Skin: Soap wash immediately - If this chemical contacts the skin, immediately wash the contaminated skin with soap and water. If this chemical penetrates the clothing, immediately remove the clothing, wash the skin with soap and water, and get medical attention promptly.; Breathing: Respiratory support; Swallow: Medical attention immediately - If this chemical has been swallowed, get medical attention immediately. 출처: The National Institute for Occupational Safety and Health (NIOSH)
  • Signal: Danger 출처: Regulation (EC) No 1272/2008 of the European Parliament and of the Council
  • GHS Hazard Statements: H302: Harmful if swallowed [Warning Acute toxicity, oral]; H314: Causes severe skin burns and eye damage [Danger Skin corrosion/irritation]; H317: May cause an allergic skin reaction [Warning Sensitization, Skin]; H318: Causes serious eye damage [Danger Serious eye damage/eye irritation]; H334: May cause allergy or asthma symptoms or breathing difficulties if inhaled [Danger Sensitization, respiratory]; H372: Causes damage to organs through prolonged or repeated exposure [Danger Specific target organ toxicity, repeated exposure] 출처: Regulation (EC) No 1272/2008 of the European Parliament and of the Council
  • Precautionary Statement Codes: P233, P260, P261, P264, P264+P265, P270, P271, P272, P280, P284, P301+P317, P301+P330+P331, P302+P352, P302+P361+P354, P304+P340, P305+P354+P338, P316, P317, P319, P321, P330, P333+P317, P342+P316, P362+P364, P363, P403, P405, and P501 (click each P-code to see the statement) 출처: Regulation (EC) No 1272/2008 of the European Parliament and of the Council
  • Note: This chemical does not meet GHS hazard criteria for < 0.1% (2 of 4575) of reports. 출처: European Chemicals Agency (ECHA)
  • Signal: Danger 출처: European Chemicals Agency (ECHA)
  • GHS Hazard Statements: H302 (> 99.9%): Harmful if swallowed [Warning Acute toxicity, oral]; H314 (> 99.9%): Causes severe skin burns and eye damage [Danger Skin corrosion/irritation]; H317 (> 99.9%): May cause an allergic skin reaction [Warning Sensitization, Skin]; H318 (26.1%): Causes serious eye damage [Danger Serious eye damage/eye irritation]; H334 (> 99.9%): May cause allergy or asthma symptoms or breathing difficulties if inhaled [Danger Sensitization, respiratory]; H372 (16.8%): Causes damage to organs through prolonged or repeated exposure [Danger Specific target organ toxicity, repeated exposure] 출처: European Chemicals Agency (ECHA)
  • Precautionary Statement Codes: P233, P260, P261, P264, P264+P265, P270, P271, P272, P280, P284, P301+P317, P301+P330+P331, P302+P352, P302+P361+P354, P304+P340, P305+P354+P338, P316, P317, P319, P321, P330, P333+P317, P342+P316, P362+P364, P363, P403, P405, and P501 (click each P-code to see the statement) 출처: European Chemicals Agency (ECHA)
  • ECHA C&L Notifications Summary: Aggregated GHS information provided per 4575 reports by companies from 67 notifications to the ECHA C&L Inventory. Each notification may be associated with multiple companies.; Reported as not meeting GHS hazard criteria per 2 of 4575 reports by companies.; There are 66 notifications provided by 4573 of 4575 reports by companies with hazard statement code(s).; Information may vary between notifications depending on impurities, additives, and other factors. The percentage value in parenthesis indicates the notified classification ratio from companies that provide hazard codes. Only hazard codes with percentage values above 10% are shown. For more detailed information, please visit ECHA C&L website. 출처: European Chemicals Agency (ECHA)
  • Signal: Danger 출처: NITE-CMC
  • GHS Hazard Statements: H302: Harmful if swallowed [Warning Acute toxicity, oral]; H314: Causes severe skin burns and eye damage [Danger Skin corrosion/irritation]; H317: May cause an allergic skin reaction [Warning Sensitization, Skin]; H318: Causes serious eye damage [Danger Serious eye damage/eye irritation]; H334: May cause allergy or asthma symptoms or breathing difficulties if inhaled [Danger Sensitization, respiratory]; H370: Causes damage to organs [Danger Specific target organ toxicity, single exposure]; H372: Causes damage to organs through prolonged or repeated exposure [Danger Specific target organ toxicity, repeated exposure]; H373: May causes damage to organs through prolonged or repeated exposure [Warning Specific target organ toxicity, repeated exposure]; H402: Harmful to aquatic life [Hazardous to the aquatic environment, acute hazard]; H412: Harmful to aquatic life with long lasting effects [Hazardous to the aquatic environment, long-term hazard] 출처: NITE-CMC
  • Precautionary Statement Codes: P233, P260, P261, P264, P264+P265, P270, P271, P272, P273, P280, P284, P301+P317, P301+P330+P331, P302+P352, P302+P361+P354, P304+P340, P305+P354+P338, P308+P316, P316, P317, P319, P321, P330, P333+P317, P342+P316, P362+P364, P363, P403, P405, and P501 (click each P-code to see the statement) 출처: NITE-CMC
  • GHS Hazard Statements: H302: Harmful if swallowed [Warning Acute toxicity, oral]; H311: Toxic in contact with skin [Danger Acute toxicity, dermal]; H314: Causes severe skin burns and eye damage [Danger Skin corrosion/irritation]; H317: May cause an allergic skin reaction [Warning Sensitization, Skin]; H318: Causes serious eye damage [Danger Serious eye damage/eye irritation]; H330: Fatal if inhaled [Danger Acute toxicity, inhalation]; H334: May cause allergy or asthma symptoms or breathing difficulties if inhaled [Danger Sensitization, respiratory]; H370: Causes damage to organs [Danger Specific target organ toxicity, single exposure]; H371: May cause damage to organs [Warning Specific target organ toxicity, single exposure]; H372: Causes damage to organs through prolonged or repeated exposure [Danger Specific target organ toxicity, repeated exposure]; H373: May causes damage to organs through prolonged or repeated exposure [Warning Specific target organ toxicity, repeated exposure] 출처: NITE-CMC
  • NFPA Health Rating: 3 - Materials that, under emergency conditions, can cause serious or permanent injury. 출처: Hazardous Substances Data Bank (HSDB)
  • NFPA Fire Rating: 1 - Materials that must be preheated before ignition can occur. Materials require considerable preheating, under all ambient temperature conditions, before ignition and combustion can occur. 출처: Hazardous Substances Data Bank (HSDB)
  • NFPA Instability Rating: 1 - Materials that in themselves are normally stable but that can become unstable at elevated temperatures and pressures. 출처: Hazardous Substances Data Bank (HSDB)
  • Toxicity Summary: IDENTIFICATION AND USE: Maleic anhydride is a solid substance appearing as colorless needles or white crystalline solid. Maleic anhydride is an intermediate, which is used in a wide range of products, mainly in the manufacture of unsaturated polyester resins. HUMAN EXPOSURE AND TOXICITY: Maleic anhydride is irritating to skin in humans. Severe skin burns and itching have been reported following dermal contact. Dust or vapor has been reported to cause conjunctivitis, inflammation and swelling of the eyelids, severe lacrymation and photophobia. Case reports of respiratory irritation, and feelings of nasal irritation and pulmonary discomfort in a volunteer study indicate that maleic anhydride is a respiratory irritant. In the volunteer study, impairment of smell was also reported. A single worker showed a positive skin reaction to a patch test, indicating that skin sensitisation was present. Repeated exposure of workers is associated with asthma as evidenced by a number of case reports. It is not known if the asthma has an immunological background. ANIMAL STUDIES: Inhalation exposure for 6 hours to up to 199 mg/cu m of maleic anhydride vapor did not cause mortality in rats. At the hig 출처: Hazardous Substances Data Bank (HSDB)
  • Environmental Bioconcentration: An estimated BCF of 5 was calculated in fish for maleic anhydride(SRC), using an estimated log Kow of 1.62(1) and a regression-derived equation(1). According to a classification scheme(2), this BCF suggests the potential for bioconcentration in aquatic organisms is low(SRC). In addition, maleic anhydride hydrolyzes rapidly in water forming maleic acid with hydrolysis half-lives of 3.32 and 0.37 minutes at 0 and 25.1 °C respectively(3). Bioconcentration of maleic anhydride in aquatic organisms is unlikely due its rapid hydrolysis(SRC). 출처: Hazardous Substances Data Bank (HSDB)
  • Environmental Fate: TERRESTRIAL FATE: Based on a classification scheme(1), an estimated Koc value of 1(SRC), determined from a structure estimation method(2), indicates that maleic anhydride is expected to have very high mobility in soil(SRC). However, maleic anhydride hydrolyzes rapidly in water forming maleic acid with hydrolysis half-lives of 3.32 and 0.37 minutes at 0 and 25.1 °C respectively(3). Therefore, potential leaching in soil is expected to be dominated by degradation to maleic acid(SRC). Volatilization of maleic anhydride from moist soil surfaces is not expected to be an important fate process due to hydrolysis(SRC). Maleic anhydride is not expected to volatilize from dry soil surfaces(SRC) based upon a vapor pressure of 0.25 mm Hg at 25 °C(4). Various biodegradation screening tests have found maleic anhydride to be readily biodegradable(5,6). However, available biodegradation rates for maleic anhydride are expected to reflect the hydrolysis product maleic acid(SRC). 출처: Hazardous Substances Data Bank (HSDB)
  • Environmental Fate: AQUATIC FATE: Based on a classification scheme(1), an estimated Koc value of 1(SRC), determined from a structure estimation method(2), indicates that maleic anhydride is not expected to adsorb to suspended solids and sediment(SRC). Volatilization from water surfaces is expected(3) based upon an estimated Henry's Law constant of 3.9X10-6 atm-cu m/mole(SRC), developed using a fragment constant estimation method(2). However, maleic anhydride hydrolyzes rapidly in water forming maleic acid with hydrolysis half-lives of 3.32 and 0.37 minutes at 0 and 25.1 °C, respectively(3). Therefore, volatilization is not expected to be an important fate process in water due to hydrolysis(SRC). Bioconcentration of maleic anhydride in aquatic organisms is unlikely due its rapid hydrolysis(SRC). Various biodegradation screening tests have found maleic anhydride to be readily biodegradable(5,6). However, available biodegradation rates for maleic anhydride are expected to reflect the hydrolysis product maleic acid(SRC). 출처: Hazardous Substances Data Bank (HSDB)
  • Environmental Fate: ATMOSPHERIC FATE: According to a model of gas/particle partitioning of semivolatile organic compounds in the atmosphere(1), maleic anhydride, which has a vapor pressure of 0.25 mm Hg at 25 °C(2) is expected to exist solely as a vapor in the ambient atmosphere. Vapor-phase maleic anhydride is degraded in the atmosphere by reaction with photochemically-produced hydroxyl radicals(SRC); the half-life for this reaction in air is estimated to be 11 days(SRC), calculated from its rate constant of 1.45X10-12 cu cm/molecule-sec at 23 °C(3). Vapor-phase maleic anhydride is also degraded in the atmosphere by reaction with ozone(SRC); the half-life for this reaction in air is estimated to be 6.5 days, calculated from its estimated rate constant of 0.18X10-17 cu cm/molecule-sec at 25 °C that was derived using a structure estimation method(4). The nitrate radical (NO3) is the dominant atmospheric oxidant during the night-time in most atmospheric environments(5). Vapor-phase maleic anhydride is degraded in the atmosphere by reaction with nitrate radicals(SRC); the half-life for this reaction in air is estimated to be 8 hours(SRC), calculated from its rate constant of 1.0X10-13 cu cm/molecule-sec 출처: Hazardous Substances Data Bank (HSDB)
  • Industry Uses: Binder; Monomers; Not Known or Reasonably Ascertainable; Stabilizing agent; Dehydrating agent (desiccant); Intermediate 출처: EPA Chemical Data Reporting (CDR)
  • Uses: Maleic anhydride is used primarily in the formation of unsaturated polyester resins for use in boats, autos, trucks, buildings, piping, and electrical goods. Lube oil adhesives synthesized from maleic anhydride are used to prolong oil-change intervals and improve engine efficiency. Maleic anhydride is also used to make copolymers, pesticides, and other organic compounds, and in Diels-Alder syntheses. 출처: EPA Hazardous Air Pollutants
  • Sources/Uses: Used in Diel-Alder syntheses; copolymerization reactions; and manufacturing of alkyd-type resins, dye intermediates, pharmaceuticals, and pesticides (Malathion). [Merck Index] Other uses are coatings, epoxies, and paper sizing resins; [ACGIH] 출처: Haz-Map, Information on Hazardous Chemicals and Occupational Diseases
  • Industrial Processes with risk of exposure: Pulp and Paper Processing [Category: Industry]; Painting (Pigments, Binders, and Biocides) [Category: Paint]; Plastic Composites Manufacturing [Category: Industry] 출처: Haz-Map, Information on Hazardous Chemicals and Occupational Diseases
  • Uses: In Diels-Alder syntheses (as a dienophile), manufacture of alkyd-type of resins, dye intermediates, pharmaceuticals, agricultural chemicals (maleic hydrazide, malathion), in copolymerization reactions. 출처: Hazardous Substances Data Bank (HSDB)
  • Uses: ... Fumaric and tartaric acid manufacture; pesticides; preservative for oils and fats; permanent-press resins (textiles), Diels-Alder reactions. 출처: Hazardous Substances Data Bank (HSDB)
  • Uses: Because of its properties as a dicarboxylic anhydride with a double bond, MA /maleic anhydride/ can be used for both polycondensation and polyaddition. Polyester and alkyd resins, lacquers, plasticizers, copolymers, and lubricants are the most important technical end products. Examples of industrially important copolymers are: MA-styrene (for engineering plastics) and MA-acrylic acid (used in the detergent industry). Polyester and alkyd resins, in particular, are used in the production of fiberglass reinforced plastics, in the construction and electrical industries, and in pipeline and marine construction. ... Smaller amounts of MA are used in the production of pesticides (captan, malathion) and growth inhibitors (maleic acid hydrazide). ... When added to drying oils, MA reduces the drying time and improves the coating quality of lacquers. 출처: Hazardous Substances Data Bank (HSDB)
  • Uses: Chem int for lube oil dispersants & corrosion inhibitors 출처: Hazardous Substances Data Bank (HSDB)
  • Uses: For more Uses (Complete) data for MALEIC ANHYDRIDE (16 total), please visit the HSDB record page. 출처: Hazardous Substances Data Bank (HSDB)

매핑 기준: Existing checksum-valid CAS to unique PubChem CID match. 가져온 시각: 2026-08-31. 출처 기록 열기

과학적 분류와 유해성 주석은 맥락을 제공할 뿐이며, 위에 표시된 시장별 규제 판단을 대체하지 않습니다.

추가 출처 적용 범위 및 일치 상태
출처결과확인됨
NIH PubChem PUG-View정확히 일치2026-08-31

기록된 불일치는 출처를 확인했다는 유용한 근거이며, 해당 물질이 다른 곳에 존재하지 않는다는 주장이 아닙니다.

체크섬이 유효한 CAS 일치를 통해 2026-08-31에 NIH PubChem에서 가져왔습니다. 화학적 특성은 이 페이지의 규제 판단을 대체하지 않습니다.

추가 공신력 있는 물질 조사

각 링크는 해당 출처에서 이 정체를 검색합니다. 링크는 조사 경로일 뿐이며, 그 출처에 정확히 일치하는 기록이 있다는 주장이 아닙니다. 각 출처의 성격과 법적 비중

이 기록 활용하기

처방에서 선별독립 비교 열기

공식 출처 및 범위

집행위원회 시행결정 (EU) 2025/1175(데이터세트 버전 EU 2025/1175)에서 가져왔습니다. 이 용어집은 제19조 제1항 (g)호에서 요구하는 성분 목록에 사용할 일반 원료 명칭을 제공하며, 승인 또는 안전성 목록이 아닙니다.

공식 결정 열기